欧美xxxx色视频在线观看,欧美肥婆性猛交xxxx

TranslationMobile

支承表面

"support" in Chinese : vt. 1.支承，支撐；支持；支援，維護。 2.援助；擁 ...
"surface" in Chinese : n. 1.表面；地面；水面；廣場，空地。 2.外觀，外表 ...
"controlled surface porosity support" in Chinese : 可控表面孔度支持體; 可控表面孔率載體
"parting surface support balance" in Chinese : 承壓平面平衡
"support surface absorption" in Chinese : 載體表面吸附作用
"support surface adsorption" in Chinese : 載體表面吸附作用
"surface support unit" in Chinese : 海面支持設備
"surface support vessel" in Chinese : 海面補給船; 水面支持船
"in support" in Chinese : 后備
"in support of" in Chinese : 考慮到這種情況; 維護…；支持…；證實…; 以便支持; 以便支援; 支持, ...
"support" in Chinese : vt. 1.支承，支撐；支持；支援，維護。 2.援助；擁護，贊助。 3.扶養 ...
"support for" in Chinese : 對……的支持
"support in" in Chinese : 碰網柱好球
"of a surface" in Chinese : 面元素
"of the surface" in Chinese : 表面上, 外表上

Examples

The clamps should be stable , the clamping force should be in normal direction to the support surface
5夾緊器要穩定可靠，夾緊方向按定位面法線方向。
Top - directly as a basis and foundation of the bearing surface as the top - embedded steel bearings or bearing surface , the supporting surface , the anchor bolt ( anchor ) position should be consistent with the allowable deviation of norms
基礎頂面直接作為柱的支承面和基礎頂面預埋鋼板或支座作為柱支承面時，其支承面、地腳螺栓（錨栓）位置的允許偏差應符合規范的規定。
This paper discusses the performance of load bearing under different boundary conditions by model test and finite element analysis . the x - side binding of the supporting surface connecting with up - side chord member of slice arch is the most important factor that affects membrane effect of the slab . the load bearig capacity of the slab with fixed end increased forty percent of the capacity of the simple - supported slab , because membrane effect of the slab with fixed end is remarkable
本文通過模型試驗和有限元分析，較深入地探討了在不同邊界條件下微彎板的受力性能，結果發現與拱片上弦桿連接的支承面有側向約束條件是影響微彎板的薄膜效應最重要的因素，當該支承面為固結狀態時，薄膜效應十分顯著，其承載力比簡支約束微彎板的承載力提高了約40 。
According to former references , the nascent metal surface usually is gained by cutting , but the manner results many pits and crevices in it and the surface is so rough that ca n ' t provide lipid molecules with smooth surface to bind to the support surface . so it brings the difficulty to recur measurement and to compare the results . the thesis brings forward a new method to get more smooth surface by sand paper
根據文獻提供的方法，通常采用剪切的方式處理覆膜的金屬表面端，由于用此方法生成的金屬端面極為粗糙，不能保證每次剪切后金屬端面的一致性，從而使所覆的blm膜不是在同一工作環境、同一工況下進行，給實驗的再現性帶來困難，同時難于進行實驗結果的前后對比分析。