- 程式設計演算法
- 程序設計算法
下載手機詞典可隨時隨地查詞查翻譯
algorithm programming中文什么意思
例句與用法
- 更多例句： 上一頁 下一頁
- Secondly , basing on single channel if sr receiver mathematic model , this thesis has designed if sr receiver subsystem and brought forward its design project and system circuit principle diagram , and explained the system working principle . furthermore , this thesis introduces the working principles and respective applications of wideband high - speed adc ad6640 , ddc ad6620 and high - speed dsp tms320c6713 according with the if sr receiver subsystem high - speed analog digital conversion department , digital down conversion department and high speed digital signal processing department . thirdly , the thesis emphatically demonstrates the software realization department of the if sr receiver subsystem , which including ad6620 ' s inner parameter software setup , tms320c6713 data transmission and processing and the quadrant demodulation algorithm program realization
其次，基于單通道中頻軟件無線電接收機數學模型，本文設計了中頻( if ， intermediatefrequency )軟件無線電接收機子系統，給出了中頻軟件無線電接收機子系統的設計方案和系統電路原理圖，說明了系統工作原理，并分別對應系統中的高速模數轉換部分、數字下變頻部分、基帶數字碩士學位論文軟件無線電理論研究及中頻軟件無線電接收機子系統設計信號處理部分，介紹了高速adcad664o ，數字下變頻器( ddc ， digitaldownconverter ) ad6620 ，高速數字信號處理器( dsp ， digitalsignalproeessor ) tms320c6713的工作原理，以及它們?cè)谥蓄l軟件無線電接收機子系統中的應用。 - In this thesis , at first introduce the general principle of gpr , next analyze the signal model of gpr and also declare the signal process theories used in this thesis and at last accomplish the clutter reduction and synthetic aperture algorithm program using matlab and also identify the algorithm program through the simulation of two groups of actual measurement data
本文中首先介紹了探地雷達的一般原理；其次分析了探地雷達回波數據的信號模型并說明了本文中用到的信號分析的方法；最后針對雜波抑制和合成孔徑這兩部分處理在matlab軟件環境中設計完成算法程序，并通過實測數據仿真驗證算法的正確性和效果。 - Agv ( automated guided vehicle ) optimization is a typical np problem , in the course of initial group generation , this article applied accumulator process , crossover operator based continuous insertion heuristic mode , and push - connect - exclude method . according to stacker running process and characteristics , stacker optimization was devided into two parts , the first one was shelves number optimization , the second one was travel scheduling problem . finally , this article written genetic algorithm program based on c
Agv的優化調度屬于典型的np問題，在初始群體的產生中，采用聚加過程，并建立了可行插入的條件；提出了基于連續插入啟發式的交叉算子；采用了推?銜接?排除過程來使任務的滿意度達到最佳；針對堆垛機的運行過程，建立了數學模型，并依據其運行特點，把堆垛機的優化分為兩部分，一是針對庫位號的優化，改變傳統的庫位號排列方式，利用遺傳算法建立起比較合理的庫位號排列順序；二是把堆垛機的運行線路簡化為旅行商問題，并做了適當?shù)男薷摹? - The g . 729 speech - compressing algorithm , written in c language , produces a huge amount of program codes , which cannot be stored in the chip - memory of dsp because of its 16k storing space . therefore , g . 729 speech - compressing algorithm written in c language is faced with the problems of low processing speed , and synthesis ( or real time ) . the main goal of this paper is to accomplish g . 729 speech signal compressing algorithm programmed in c54x general assembly language , and to overcome the problems above
在利用tms320vc5402進行語音信號壓縮處理時，其開發軟件提供了支持c等高級語言編譯器，但該dsp的片上存儲空間僅有16k ，如果選用c語言編程實現g . 729語音壓縮算法，程序代碼量過大很難都存放在片內存儲器，這樣運算速度降低，很難解決實時(或同步)問題。 - The proposed driving circuit includes a low - pass filter circuit 、 feedback circuit 、 signal generated circuit 、 phase shifted circuit and power inverter circuit . a ti cooperation ' s dsp ( tms320lf2407a ) is chosen for the drive and control system based on the characteristics of usm , the interface circuit 、 each function ’ s flow chart and algorithm program are designed
根據usm的特點,選取一款專用于電機控制的dsp芯片tms320lf2407a ,設計了硬件接口電路、各功能部分的流程圖及控制算法程序,以ccs為編譯環境,進行電機整個控制系統的軟件編寫與調試。