multi-load造句
例句與造句
- Taking into consideration multi - load level , we carry out three types of generating deviation standards and describe their characteristics
按照發電偏離電量對電網運行的影響，提出了3種偏離程度的認定與劃分判據。 - At the end of the dissertation , example calculation is given under multi - loading cases using the agc software of hydropower station based on dcpm - fga
最后，運用所設計的水電站廠內agc控制軟件對某電站進行了多個功率點多工況條件下的實例計算。 - The results by exemplification expatiate that this method can not only be used directly to work out the optimum structural design with discrete variables to constraints stress and cross - section area , but also can deal with the discrete structural optimization featured with multi - loading , multi - constraints and multi - variables
算例結果表明，該方法能直接計算具有應力約束和截面尺寸約束的離散變量結構優化問題，也能處理同時具有穩定約束和位移約束的多工況、多約束、多變量的離散變量結構優化設計問題。 - 6 the optimal design mathematics models and calculations of the multi - source and multi - load looped network which source pressure and flow is undecided and the multi - source and multi - load looped network which source pressure and flow is decided are presented respectively , according to analysis load of multi - source looped network
6在分析了多水源環狀管網工況的基礎上，分別建立了多工況條件下水源水壓和流量未定多水源環狀管網以及水源水壓和流量已定多水源環狀管網優化設計數學模型，并提出了計算方法。 - In chapter five , algorithm of load identification is discussed in detail . levenberg ? marquardt algorithm and generalized regression neural network are used to identify the position and degree of the one load on the surface of the airfoil , correlation analysis algorithm of multi - load identification is also proposed in the paper
第五章重點論述了系統設計中的載荷識別算法,采用人工神經網絡lm - bp算法及廣義回歸網絡對單個載荷大小、位置進行了判定,提出了基于相關分析的多載荷識別算法。 - It's difficult to find multi-load in a sentence. 用multi-load造句挺難的
- The evolution laws of structural weight , the best optimum fitness , average fitness , maximum nodal stress and displacement with increasing generations are discussed . and multi - result fact of the topology optimization can be obtained by ga - fem . the research results in this thesis show that the developed method is successful in the topology optimization for 2d continuum structures under multi - load and multi - constrain conditions
上述工作表明，本文ga ? fem可以實現多載荷、多約束條件下平面連續結構拓?fù)鋬?yōu)化，與eso等優化方法獲得的優化結果相比，本文的優化結果不存在單元鉸接和不連續單元，優化結構多樣，質量更小，效果更優。