task n. 1.(派定的)工作,任務,功課。 2.艱苦的工作,苦差使。 3.〔廢語〕租稅,稅款。 set (sb.) a task 派(某人)一個任務。 be at one's task 在做著工作。 It's quite a task to figure out 10 problems in an hour. 一小時內算出十道習題可是個艱苦的工作。 bring [call, take] sb. to task (for doing sth.) (為…)責備(某人)。 take a task upon oneself 接受任務。 vt. 1.派給工作。 2.虐待,使作苦工。 3.〔廢語〕課稅。 task one's energies 盡全力。 taskbar 【計算機】(通常顯示于電腦屏幕底部的)任務欄。
In this paper , the task programming and the decompose strategy based on the structure property are developed . the detail method of task decompose is also developed aim at the character of the dispatching operation in power system 提出了基于結構屬性分析的mas任務規劃和分解策略,并且針對電網調度操作的特點,提出其具體的任務分解方法。
However , nowadays embedded applications tend to be more complicated and most of them provide os support and adopt multi - task programming . all above require cross - debugger that can provide special task - level debugging support 而當今嵌入式應用日趨復雜,多半有操作系統支持,采用多任務編程,這就要求交叉調試器能提供任務級的特殊調試支持。
Mainly discuss the choice of gateway hardware platform , specifically introduced the programming of the gateway , the operate of can controller , the design of can data send and receive programming , network programming and the multi - task programming with emphasis 軟件設計介紹了交叉開發環境keiluvision2ide的設置和調試手段,給出了對can控制器的操作、 can數據幀處理程序設計、網絡編程,其中重點討論了嵌入式多任務程序的設計。
The processor which was adopted in the design is atmega128 , this is a low - power cmos 8 - bit microcontroller based on avr enhanced risc architecture . the software adopts the real - time kernel c / os - , the step we do first is the transplanting of the os , the next is to divide the multitask in accordance with the all function of the system and define the pri of each task , the final is to finish the task program 本設計采用了愛特美爾公司的高檔avr高速單片機atmega128作為系統的微處理器;同時在軟件設計上采用了源代碼開放的實時嵌入式多任務操作系統c os - ,將c os -操作系統移植到單片機上,將系統所要實現的功能分成多個任務分別設計任務程序,在操作系統的調度管理下進行系統的運行。
Aim at the character of process implementation of ve , the dissertation combines the project management with workflow management tightly . it uses the project dissolution and task programming method to plan the project implementation schedule , uses workflow management system to allocate the task and watch the schedule of process implementation , and it also executes the task by project control and workflow adjusting 本文針對虛擬企業過程實施的特點,將項目管理同工作流管理有機地結合起來,利用項目管理中的項目分解方法和任務規劃方法制定過程實施的進度計劃,利用工作流管理系統進行任務的分派并監控過程實施的進度。
Secondly , on the basis of the basic structure of the brake control system , the theory of brake task programming is studied and analyzed thoroughly . on the condition of automatic train protection , the fixed block system and moving block system the brake task programming method is brought forward 其次,本文從制動控制系統的基本結構出發,對制動任務規劃理論進行了詳細的研究和分析,分別提出了在基于安全防護、固定閉塞和移動閉塞三種不同應用條件下的制動任務規劃方法。
Firstly , in this thesis the dynamic model of the low - speed maglev train is analyzed . on the analysis of the principle of electric brake and mechanical brake the structure of electric - mechanical brake control system is set up . the concept of brake task programming and electric - mechanical brake controller is put forward 首先,本文通過分析低速磁浮列車的動力學模型,研究了低速磁浮列車電制動和機械制動的原理,分析和構建了電-機械聯合制動控制系統的結構,提出了制動任務規劃器和電-機械聯合制動控制器的概念。
其他語種釋義
task programとは意味:task program タスクプログラム[機械]〈98B0134:産業用マニピュレーティングロボット―用語〉