口模的英文

發音:

英文翻譯
造句

neck ring mold

口 mouth
模 mould; pattern; matrix
敞口模 chunk; open-top mold
澆口模 gating pattern
口模圈 die ring
口模套 die bushing
口模緣 die relief
擴口模 expanding die; flaring dies
切口模 lancing die; notching dies
缺口模 notch punching die
縮口模 blanking-slotting die; necking dies; neckling die
鎖口模 counter locked die
咬口模 lock die
敞口模具 chunk
沖缺口模 piercing die
窗口模式 window mode; windowmode; wwm
窗口模型 window model
單澆口模 single gate mold
端口模式 port mode
多?？谀ｎ^ family die
港口模型 harbor model
河口模型 estuarial model; estuary model
環形口模隙 annular die gap
接口模件 interface module
接口模塊 eaim eatm interface module eatm; iinterface module; im interface module; interface module

"查查詞典"手機版

千萬人都在用的超大詞匯詞典翻譯APP

例句與用法

Design of a die for extrusion of the plastics profile with an irregular cross - section with fem
異型材擠塑口模的有限元設計
Numerical simulation of three dimensiona isothermal power - law polymer melt flow within an extrusion die with the quot; l quot; shaped cross section
型異型材擠出口模內聚合物熔體三維等溫冪律流動的數值模擬
Numerical simulation and analysis of polymer melt filling flow driven by a periodically oscillating entrance pressure through the extrusion die with an irregular cross - section
振動場作用下聚合物熔體在異型材擠出口模內的充填流動分析
With the development of plastic door - window , more effective design method of plastic profile die is required . function block usually is a dependency on the main profile , but it has important effect on the main profile melt flow and the quality of the profile die
功能塊在模頭口模中一般是附屬在主型材上，但它對主型材熔體在口模中的流動以及型材的整體質量卻有著不可忽視的影響。
Abstract : in order to eliminate the product defects such as deformation , corrugation and rupture , the authors put forward the principle of flow rate uniformity for the design of rubber and plastics profile extrusion dies . on the basis of this principle and through the rheologic analysis of some actual cases , the design procedure is demonstrated
文摘:為解決擠出制品的扭曲變形、起皺、破裂等問題，本文提出了橡塑異型材擠出口模設計的流率平衡原則，并據此原則通過對具體例子的流變學分析，提出了口模設計方法。
A new method should be discovered to design the function block . the thesis is based on the rheology and hydrokinetics of the polymer melt , and calculates the velocity in the die by fem simulation , and provides die design with theory proof . according to the existed theory , i summarize and conclude the fem formula of the polymer flow , and then write the program to calculate on the computer
本論文中功能塊結構的研究，是以熔體的流變性以及流體動力學理論基礎上，對在口模中的熔體進行數值模擬，計算出熔體在口模中的流動參數(主要是速度的分布) ，從而可以科學的對功能塊幾何結構進行優化。