孔位置的英文

發音:

英文翻譯
造句

hole site

孔 hole; opening; aperture
位置 seat; place; location; site
鼻孔位置 nostril position
穿孔位置 punch position; punching position
井孔位置 position of well
嵌環孔位置 thimble location; thin shade
中心孔位置 zentrier-lochlage centering hole position
鉆孔位置層 drill layers
數字穿孔位置 digit-punching position
鉆孔位置測量 bore-hole position survey; bore―hole position survey
孔位 hole location; hole site
定孔位 make location
孔位圓 bc(bolt circle); bolt circle
鉆孔位 drilling position
y穿孔位 y punch
第11穿孔位 eleven punch; eleven-punch
定孔位日期 date of location
孔位錯誤 mis hole location
孔位破出 hole breakout
孔位誤差 hole position tolerance
孔位座標表 hole location chart
選定孔位 location of hole
孔位破出破壞 hole breakout
位置 1.(所在或占的地方) seat; place; location; site 大家都按指定的位置坐了下來。 everybody took their places.2.(地位) place; position 她曾是個在政府中占有重要位置的女人。 she was a woman of high position in the government.3.[航] position
所接插座的孔位 ic

"查查詞典"手機版

千萬人都在用的超大詞匯詞典翻譯APP

例句與用法

The experiment also proves that it is important that the position and order of grouting holes are arranged properly
試驗還表明，合理的布置注漿孔位置和安排注漿順序對于更有效的實現頂升效果具有很大的作用。
Based on research of the antenna assemble procedure , the simulation model of the reflector is set up and error modeling and simulation of position of stick holes , grid bar acrossing the hole and rms of reflector face are achieved
在分析柵格天線裝配過程基礎上，建立了其反射面裝配的仿真模型，并對柵支板中心圓孔位置誤差、柵條穿人誤差和柵面誤差進行了建模與仿真計算。
Results show that the influence of mainstream reynolds numbers on heat transfer coefficience is little and the heat transfer coefficience raise with the increase of reynolds numbers . the influence of the position of holes on heat transfer coefficience is complex and correlate with the mainstream speed and the balde surface curvature . and the influence of blowing ratio on heat transfer coefficience is more great ( especially to stator ) , and show a complex relation to mainstream reynolds number and the position of holes
實驗結果表明，不同孔位出流的換熱由于孔排下游表面來流速度及葉片表面曲率的不同而有不同的規律，而主流雷諾數對葉片表面特別是壓力面和前緣區域的換熱系數比的影響較小，吹風比對換熱系數影響較大(特別是導葉) ，并且隨氣膜孔位置和來流雷諾數的變化而情況復雜。
Modeling the general solid web continuous box girder and opening - in - web ( open web ) continuous box girder by ansys finite element modeling tool , node stress of governing section and corresponding shear lag values are analyzed . the solution is validated by comparing with variational results and modeling test values . based on the model , the section shear lag induced by dead load , prestress tendons and car loads under the most unfavorable condition and lateral symmetry are also approached . the influence of shear lag effect in double - level continuous box girder is considered with opening - in - web and the web location . the analysis indicates that double - level - load arouses less shear lag effect than one - level - load . when self - weight and prestressed tendons act on together , the shear lag effect on box girder take on a evidently change
基于所建立的有限元模型，本文分別對實腹和腹板開孔兩種箱梁在恒載、車載、預應力荷載作用時，各主要截面的剪力滯效應進行分析，通過施加縱向最不利的和橫向對稱的車輛荷載，研究實腹連續箱梁和空腹連續箱梁在承受雙層荷載和單層荷載時引起的剪力滯效應，并考慮腹板開孔及開孔位置對于連續箱梁剪力滯效應的影響。分析表明，雙層車載對于箱梁引起的剪力滯系數比單層車載的影響要小，對于箱梁中存在引起的剪力滯后現象有一定的改善作用。
Then the writer finished elastic and nonlinear analysis to slabs with different openings and different boundary by finite calculation . and the writer made comparison to all dates and got the change rule of the stress , displacement , limit load and crack of slabs with openings where changing the each parameter
接著，筆者采用有限元程序對不同開孔大小、不同開孔位置、不同的邊界條件進行了彈性和塑性分析，并結合實驗數據和前人數據，分析出各種不同條件下開孔板在孔口應力、撓度、極限承載力、裂縫形式等的變化規律。
From the study results it is showed that turret hole position near the forward of the midship has less effect to the ship girder strength and it is more reasonable using probabilty statistics method to estimate the extreme value of wave bending moment , by which the first approximate value of hull midship section modulus can be determined
研究結果表明：轉塔開孔位置在舯前附近對船體總強度影響不大；波浪彎矩極值用概率統計方法估算更為合理；船體結構剖面模數的第一近似值可用波浪彎矩設計極值等來確定。