The rate of heat flow between any two points increases with difference of temperature . 任何兩點間的熱流動速率則隨溫差的加大而增加。
Difference of temperature in cross section of kiln 窯內斷面溫差
It has distinctive difference of temperature between blue moon valley and sun valley ,谷中有籃月亮峽谷和太陽谷,在兩峽谷交界
Since china covers a vast area , there is a great difference of temperature between the north and the south 列車員:由于中國土地遼闊,南方和北方的溫度相差很大。
Free adjustment design of toe cap pressing travel is never affected by the differences of temperature and pressure . it provides very stable force for pressing 鞋頭壓著行程免調設計,絲毫不受溫壓差之影響,確實提供極穩定之壓著力。
The difference of temperature fields from considering and neglecting the temperature - dependence of material parameters is compared , and the temperature distributions of al pipe are obtained in angular orientation at various time 給出了溫度隨角向的分布曲線,比較了物理參數隨溫度變化和不隨溫度變化兩種情況下溫度場的區別,并進一步得到了近場區域表面波的時域波形。
The paper combines the dashenkeng n bridge design with the method of finite elment analysis , makes computation model of bridge structure , makes use of dr . v2 . 9 refering to british bs5400 and specification of new zealand and china , analyses temperature effect of dashenkeng ii , gets the caculate result to guide construction on site : differences of temperature models reach different results 本文結合大深坑號橋的實際情況,從結構溫度效應分析的有限元法出發,建立了橋梁結構計算的模型,采用同濟大學橋梁工程系開發的《 dr bridge橋梁博士2 . 9版》平面桿系有限元分析程序參照英國bs5400規范、新西蘭規范及我國公路橋梁設計規范分別分析了大深坑橋縱向的溫度效應,并將結果予以對比。
The interactions between heat flux density , vapor pressure , vapor velocity and the coefficient of heat transfer for condensation in tube , the coefficient of heat transfer in total are investigated . the relationships between heat flux density and the total difference in temperature , the difference of temperature , pressure drop of vapor from the entrance of the tube to the exit are investigated as well 考察了冷卻水流量、溫度恒定條件下熱流密度、蒸汽壓力、蒸汽流速對冷凝傳熱膜系數及總傳熱系數的影響關系,同時考察了總傳熱溫差、蒸汽進出口溫差及壓差隨熱流密度變化的關系。
The suitable oil flux during the circulating of transformer could be defined according to the difference of temperature between the oil and wind in the inlet and the cooling capacity of the wind cooling system ; besides the oil flux can be determined by ultrasonic , it can be estimated whether the oil is flowing equably by determining the oil flux in the branch pipes ; reducing the oil flux of the oil pump could be realized by controlling to change its frequency , which could not only save the energy , reduce the wastage , but benefit the transformer ' s circulating safely 變壓器運行中可根據進口油溫和進口風溫之差、風冷卻器的冷卻容量來確定合適的油流量;油流量可以通過超聲波法進行測量,測量油的分管流量還可判斷油流的均勻情況;降低潛油泵流量可通過潛油泵的變頻控制來實現,不僅節能降耗,對變壓器的安全運行也有著重要意義。
It shows that the injection quantity and the difference of temperature distribute as a parabola which is at the same load , and the minimum of the parabola corresponds to the optimum quantity of injection ( g ) . under the condition that the quantity of injected mass , the air speed and the heat quantity is respectively g , v and q , the research demonstrates that the pentium iv chip ' s temperature variation can be controlled under 40c and work normally when the wind speed overpass 1 . 5m / s and the power dissipation of the chip is 60w . otherwise this paper calculates the flooding limit of thermosiphon with several different methods 對其充灌量、散熱量、電子元件( cpu模擬芯片)表面與環境溫度之差及通風、流速的影響進行了系統的測試,發現充液量與溫差的關系在負荷不變時呈拋物線分布,其極小值點對應的充液量是最佳充液量g 。在充液量為g時,對風速v 、散熱量q進行的研究表明,當風速超過1 . 5m / s后,奔騰芯片在60w發熱條件下芯片溫度小于40 ,能滿足長期正常工作。