linear adj. 1.線的,直線的。 2.長度的。 3.【數學】一次的,線性的。 4.【動、植】線狀的;細長的。 5.由線條組成的,以線條為主的,強調線條的。 linear amplification 直線放大。 a linear equation 一次方程式。 a linear leaf 線形葉。 linear arts 線條藝術。
Determination of trace fluoride in foods using linear sweep adsorptive stripping voltammetry 線性掃描吸附伏安法測定食品中痕量氟
Test method for measurement fo hindered phenolic antioxidant content in turbine oil by linear sweep voltammetry 利用線性掃描伏安法測定汽輪機油合成樹脂酚抗氧化含量的方法
Standard test method for measurement of hindered phenolic antioxidant content in hl turbine oils by linear sweep voltammetry 用線性掃描伏特計測定hl渦輪機油中的受阻礙酚型抗氧劑含量的標準試驗方法
Standard test method for measurement of hindered phenolic and aromatic amine antioxidant content in non - zinc turbine oils by linear sweep voltammetry 用線性掃描伏安法測量無鋅渦輪機油中受阻酚和芳香胺抗氧化劑含量的標準試驗方法
Its electrochemical properties were studied by means of galvanostatic discharge and linear sweep voltammetry experiments . agcuo _ 2 shows the better discharge property in alkaline electrolyte than emd 恒電流放電測試結果表明在不同放電制度下, agcuo _ 2的放電容量均遠大于emd的理論放電比容量。
The common method of disa embly , referred to as the linear sweep method , a umes that all bytes starting from the entry point of a binary ( or some start location ) are i tructio , and disa embles the entire code segment , following succe ive bytes 反匯編的通常方法,即所謂線性掃描方法,假定從二進制代碼入口點(或某開始位置)開始的所有字節是指令,并且順序反匯編整個代碼段字節。
The common method of disassembly , referred to as the linear sweep method , assumes that all bytes starting from the entry point of a binary ( or some start location ) are instructions , and disassembles the entire code segment , following successive bytes 反匯編的通常方法,即所謂線性掃描方法,假定從二進制代碼入口點(或某開始位置)開始的所有字節是指令,并且順序反匯編整個代碼段字節。
The application of semantics is discussed as follows : the projection relation semantics leading to recognizing cylinder , the region semantics leading to recognizing linear sweeping , the free element semantics leading to recognizing the feature which the cylinder is cut by plane . last , a prototype system is developed according to the semantics model . the system can read dxf that contains 2d engineering drawing information and recognize the 3d feature 接著,根據工程語義模型表述,詳細分析了各個類別、層次以及類別之間表達的工程語義的特點與內容,然后進行零件的特征分類,從特征識別的角度探討了工程語義在圖樣理解的應用,并詳細討論了圓柱體、線性拉伸體、圓柱體的平面截切特征從投影語義、連通域語義、游離圖元語義引導識別的應用過程。