It proves that the capability of wind generator is determined to slip , rotor voltage and angle between rotor voltage and stator voltage , and investigates the control model based on the stator field - oriented vector control 文中還分析了雙饋型風力發電機的轉矩特性和穩態特性,證明了發電機的性能由轉差率、轉子電壓和定轉子電壓間的相位角差決定的。
Just using the stator currents , stator voltages , and velocity , the method proposed in the paper makes real time identification of induction motor parameters based on the least squares identification algorithm . the method does n ' t use the rotor flux signal , avoiding the coupling between the rotor flux observation and the parameter identification 本文提出僅用電機的定子電流、電壓和轉速進行電機參數的辨識方法,它利用遞推最小二乘法進行在線參數辨識,該方法不需要觀測得到的磁鏈信號,消除了磁鏈觀測和參數辨識的耦合。
It also builds the mathematic model of all section of vscf ac exited wind power generation system on a - b - b and d - q coordinate system by the coordinate commutation technology . the thesis gives the characteristics of torque , active power , reactive power and the steady - state analysis of it . it proves that the capability of wind generator is determined to slip , the amplitude and phase of rotor voltage , the phase dispatch between stator voltage and rotor voltage 并分析了交流勵磁風力發電機作變速恒頻運行時的工作原理,闡述了與同步發電機、異步發電機的不同之處,分析了其能量平衡關系,在坐標變換技術的幫助下,詳細推導了交流勵磁發電機在a - b - c坐標系和d - q坐標系下的數學模型,分析并仿真了其有功和無功特性、轉矩和功率調節特性、穩態運行和機械特性,證明了發電機的性能由轉差率、轉子電壓的相位和幅值、定轉子電壓相位差所決定的。
For above purpose , we must synchronously and constantly acquire several signals , such as stator voltages , stator currents , rotor speed of asynchronous motor and so on , and synchronously save , dynamically display , fully analyze and process the acquired signals . apparently , the traditional measuring instruments ca n ' t satisfy these special requirements . if the digital storage oscilloscope is adopted to record data , it ca n ' t resolve two problems : the low storage capacity and the poor data analysis and process 為了達到上述目的,需要同步、長時間地采集異步電機端部電壓信號、電流信號、電機轉速等多路信號,并對采得的信號進行實時存儲、動態回放和分析處理,采用傳統測量?jī)x器已經不能滿足這些要求,采用數字存儲示波器記錄數據,存在存儲深度不夠及數據分析處理的問題。
The rotor velocity and position can be taken as two states variable of the system by using the ekf on the basis of the theory of the bldcm . based on the measured stator currents and stator voltages , we can estimate the rotor velocity and position . it is very useful for us to study the application of the velocity and position sensorless operation of brushless dc motor drives 在直流無刷電機的原理基礎上,利用擴展卡爾曼濾波器將轉子轉速和位置看成系統的兩個狀態變量,根據定子側可測的電流、電壓值,逐步估計出轉子轉速和位置,為無速度和位置傳感器無刷直流電機控制系統打下基礎。